Skip to content

About

Per-pin current guard for the 12V-2x6 connector of RTX 5090 cards (ROG Astral, WireView Pro II, MSI Ai-TS PSUs) – throttles, then shuts down. Linux & Windows.

Topics

Resources

Stars

0 stars

Watchers

0 watching

Forks

Latest commit

 

History

15 Commits

Folders and files

Repository files navigation

Areko GPUPinWatch

Per-pin current guard for the 12V-2x6 power connector of RTX 5090 cards – Linux & Windows
Deutsch

Melted 12V-2x6 / 12VHPWR connectors usually start with one pin carrying far more current than the others (bad contact, worn plug). Most cards cannot see this: all six 12 V pins end in one copper plane behind the connector. Areko GPUPinWatch reads the cards and devices that do measure every pin and steps in before it gets hot.

Overview (Areko theme)

What it does

Watches the six 12 V pins of every supported card, 2× per second (1/2/4 Hz)
Stage 1 – throttle a pin ≥ 8.5 A for 1 s → only that card's power limit is lowered (default 400 W)
Stage 2 – emergency shutdown still ≥ 9.2 A (the pin rating) for 1.5 s after throttling → the PC shuts down (or alarm only, your choice) and a log file is written
Alarms tray icon turns yellow/red and blinks, desktop notification, warning sound, the card in the window pulses red
Release one click gives a throttled card its previous power limit back
Window overview with plug view (12 V row + GND row), totals, spread, 60 s history, settings, event log
Looks themes Light, Dark, Areko · languages English, Deutsch, Italiano, Español, Português, 中文, 日本語

All thresholds can be changed in the settings (within safe bounds). The service runs without a logged-in user; the window is only the display.

Alarm Dark Light
Alarm Dark Light

Supported hardware

Per-pin values exist only where hardware measures them. GPUPinWatch detects everything automatically – no setup.

Cards with an on-card sensor (work with any power supply)

ASUS boards with the ITE IT8915FN monitoring chip. Detection asks the chip itself, so variants not listed here work too.

Card PCI subsystem 1043: Status
ROG Astral RTX 5090 OC 89E3 ✅ tested (Linux, 2 cards)
ROG Astral RTX 5090D OC 89EA should work, untested
ROG Astral LC RTX 5090 89EC should work, untested
ROG Astral RTX 5090 OC White 8A2E should work, untested
ROG Astral RTX 5090 BTF OC 8A5A, 8A3C should work (only when powered through the 12V-2x6 socket)
ROG Matrix RTX 5090 8A61 should work, untested
ROG Astral RTX 5080 / OC / OC White / Hatsune Miku 89DF, 89DE, 8A2B, 8A45 should work, untested

Any RTX 5090 with one of these devices

Device Connection Status
Thermal Grizzly WireView Pro II (+ Noctua Edition) USB (serial) implemented from the documented protocol, untested on a device
MSI MPG Ai1300TS PCIE5 / Ai1600TS PCIE5 power supply (GPU Safeguard+) USB (HID), up to 2 connectors implemented from the documented protocol, untested on a device

With a WireView or an MSI power supply, GPUPinWatch finds out by itself which card the connector feeds (it compares the measured current with each card's power draw).

Not supported – and why

  • Other RTX 5090 boards without one of the devices above (Founders Edition, TUF, Prime, Gigabyte, Zotac, Palit, PNY, Inno3D, MSI Gaming/Vanguard/Suprim, …): the board only measures the total current, there is no per-pin data to read.
  • MSI MAG A1000PLS / A1200PLS: protection is inside the PSU (buzzer), no data over USB.
  • Cooler Master GPU Shield: measures per pin, but has no USB/software interface.

Ground pins (GND) are never measured by any of these sensors.

Install

Windows 10 / 11

  1. Download Areko-GPUPinWatch-<version>-windows-x64.zip from Releases and unpack it.
  2. Double-click install.cmd (Windows asks for administrator rights). Alternatively, in an administrator PowerShell: powershell -ExecutionPolicy Bypass -File .\install.ps1 This copies everything to C:\Program Files\Areko GPUPinWatch, installs and starts the service Areko GPUPinWatch (starts with Windows) and adds the window to the Start menu.
  3. Remove again: double-click uninstall.cmd.

The files are not signed yet – SmartScreen may ask once ("More info" → "Run anyway"). Settings: %ProgramData%\Areko GPUPinWatch\config.toml.

Linux

Needs the NVIDIA driver (NVML) and, for ASUS cards, the i2c-dev module (the installer enables it).

  1. Download Areko-GPUPinWatch-<version>-linux-x64.tar.gz from Releases and unpack it.
  2. sudo ./install.sh – installs the service areko-gpupinwatch (systemd, root), the window areko-gpupinwatch with menu entry, and loads i2c-dev at boot.
  3. Remove again: sudo ./install.sh --entfernen

Settings: /etc/areko-gpupinwatch/config.toml. Release a throttled card from the window or with sudo systemctl restart areko-gpupinwatch (restores the previous limit).

Try it without risk

areko-gpupinwatchd --probe runs the full logic but never changes a power limit and never shuts down – it only logs what it would do. With low test values such as --probe --warn 1.0 --crit 1.05 you can watch both stages fire without real load.

Build from source

# Linux: Rust (stable), webkit2gtk4.1, libsoup3, libappindicator-gtk3 (Fedora: *-devel packages)
cargo build --release                       # service + window
sudo packaging/linux/install.sh             # uses target/release
# Windows binaries from Linux: mingw64-gcc + rust-std for x86_64-pc-windows-gnu
cargo build --release --target x86_64-pc-windows-gnu

Layout: crates/gpw-core (decoders, protection logic, IPC – no I/O), crates/gpw-sources (device access), crates/gpw-daemon (service), app/ (window, Tauri 2). Protocol facts: docs/PROTOKOLLE.md. The program only ever sends read commands to devices (allow-lists in the code).

Disclaimer

Areko GPUPinWatch does not replace a properly seated connector and good cables. It reacts to what the sensors report; it cannot see damage that has already happened. Use at your own risk.

License

PolyForm Noncommercial 1.0.0 – free for personal and non-commercial use; commercial use only with the author's permission.

Required Notice: Copyright Areko (https://github.com/arekown/Areko-GPUPinWatch)

Thank you for the protocol groundwork to: vhpwr-guard · LACT · LibreHardwareMonitor · PinSentinel · wireview-pro-ii · wireview-monitor · meltalarm · psutop · msi-psu-monitor.

About

Per-pin current guard for the 12V-2x6 connector of RTX 5090 cards (ROG Astral, WireView Pro II, MSI Ai-TS PSUs) – throttles, then shuts down. Linux & Windows.

Topics

Resources

Stars

0 stars

Watchers

0 watching

Forks

Releases

Packages

Contributors

Languages